PRODUCTS

You are straight > Home > Products > Apple iPhone 6s & Plus > iPhone 6s Plus Loudspeaker
Close】      【Print
Name:   iPhone 6s Plus Loudspeaker
ID:   1642 Size:   
Products Sort:   Apple iPhone 6s & Plus Weight:   0.0047kg

Details

Product Overview

Bad speakerphone? No speakerphone audio? This may be the part you need!

  • This part is for speakerphone and audio output.




  • Remove the single 1.4 mm Phillips screw holding the NFC bracket in place.


DSC04214 iPhone 6s Plus Loudspeaker (1).jpg




  • Remove the NFC bracket.






  • Remove the two 2.7 mm Phillips screws securing the audio control cable bracket to the logic board.



DSC04214 iPhone 6s Plus Loudspeaker (4).jpg




  • Remove the audio control cable bracket.






  • Disconnect the audio control cable by prying its connector straight up from its socket on the logic board.






  • Disconnect the cellular antenna cable by prying its connector straight up from its respective socket on the logic board.






  • Disconnect the Wi-Fi diversity antenna cable by prying its connector up from the logic board.






  • Disconnect the power button flex cable from its socket on the logic board.






  • Disconnect the Lightning connector interconnect antenna cable by prying it up from the logic board.






  • Use the flat end of a spudger to disconnect the Lightning connector flex cable from the logic board.






  • Deroute the antenna cable from the two clips on the right edge of the logic board.





  • Remove the following screws:

    • Use a small flathead screwdriver to remove this standoff screw.

    • One 1.3 mm Phillips screw

    • One 2.6 mm Phillips screw

    • One 2.2 mm Phillips standoff screw






  • Remove the bracket.






  • Deroute the upper left cellular antenna cable from the first logic board clip by nudging it out from under the clip, towards the battery.






  • Continue derouting the cellular antenna cable from the second and third logic board clips.

  • Use the pointed tip of a spudger to gently pry the cellular antenna cable from the middle logic board clip.

    • Do not pull the cable out of the center clip, as it will tear easily.

  • In order for the cable to reach its socket on the logic board, you must route it above the logic board and underneath the audio control flex cable, as shown in the first photo.





  • Remove the final 2.0 mm Phillips screw directly below the SIM card reader.


DSC04214 iPhone 6s Plus Loudspeaker (31).jpg




  • Carefully raise—but do not remove—the logic board, lifting it from the bottom edge nearest the Lightning connector.






  • Tip the logic board up to a vertical position to expose the single antenna connector on the underside, near the top edge of the board.

  • Do not attempt to fully remove the logic board yet, as the Wi-Fi/Bluetooth antenna is still connected to the underside of the board.






  • Gently lay the logic board upside-down, with the top portion resting against the rear case of the iPhone.

  • Use the flat end of the spudger to disconnect the Wi-Fi/Bluetooth antenna cable from its socket on the back of the logic board.






  • Remove the logic board.


DSC04214 iPhone 6s Plus Loudspeaker (38).jpg




  • Use the flat end of a spudger to peel the Lightning connector flex cable off the speaker.







  • Remove the following three Phillips screws from the Taptic Engine cable bracket:

    • Two 3.5 mm screws

    • One 2.7 mm screw

  • Remove  the bracket.







  • Remove the five Phillips screws securing the speaker to the rear case:

    • Two 2.7 mm screws

    • One 2.5 mm screw

    • One 1.5 mm screw

    • One 1.7 mm screw


DSC04214 iPhone 6s Plus Loudspeaker (43).jpg




  • Deroute the Wi-Fi diversity antenna cable from its rubber sleeve.

    • If the white water damage indicator sticker makes it difficult to deroute the antenna cable, gently peel the sticker back for better access.







  • Use a pair of tweezers to disconnect the Wi-Fi diversity antenna cable from the Lightning connector flex cable.






  • Remove the final 2.6 mm Phillips screw securing the speaker to the rear case.


DSC04214 iPhone 6s Plus Loudspeaker (48).jpg




  • Use the flat end of a spudger to lift the speaker assembly out of its housing.

  • Remove the speaker assembly.






  • Use a pair of tweezers to begin peeling the antenna cables off of the speaker.





  • Continue peeling the antenna cables off the long side of the speaker

  • At this point, the clip holding the antenna cables may fall off the speaker. If it does, be sure to keep track of it for reassembly.








  • Use the flat end of a spudger to pry the Wi-Fi diversity antenna off the speaker.

  • Remove the antenna.






  • Speaker remains.


DSC04214 iPhone 6s Plus Loudspeaker (60).jpg

Products Sort

    TEL: 0086-20-81277640
    map1 map2
    Copyright ©2003-2020 HongLei, All Rights Reserved.